We usually use a top round roast, but a bottom round roast should work too. If you're unsure, ask your butcher! Since the meat is slow roasted for a long amount of time, even tougher, more lean cuts of meat will be tender. Previously: beef roast grilled.
Calculate your cooking time for medium-rare with 20 mins per 500g, or for medium use 25 minutes per 500g. For beef on or off the bone cook it at 240C/220C fan/gas 9 for 20 minutes, then turn down to 180C/160C fan/gas 4 (not forgetting to take this 20 minutes off the timing you have just calculated).
Here's what I do: I put a rack in the bottom of a roasting pan. Then I place the roast (no rubs or seasonings) on the rack and cover it with a lid. I put it in the oven at 400° for 15 or 20 minutes, then turn it down to 325° and roast for 30 minutes per pound. All it does is end up tough, chewy, and well-done.
The USDA recommends steaks and roasts be cooked to 145°F (medium) and then rested for at least 3 minutes. To ensure food safety, ground beef should be cooked to a minimum 160°F (well done). Be sure to check with a thermometer, as color alone is not a foolproof indicator.
Rolled Rib Roast is the same cut as the Standing Rib Roast but with its bones removed and the meat rolled and tied into a cylindrical shape. The Rib-Eye Roast is the boneless center cut of the rib section. Very well-marbled, tender and flavorful, it is the most desirable and the most expensive of the roasts. Also check: beef roast vs pot roast.
While both are large, tough cuts of budget-friendly beef, the main difference that sets these two roasts apart is where on the animal they're cut from. Top round roast is cut from the rear leg and is more lean than chuck roast, which is cut from the shoulder and contains more fat.
Unlike any other kind of cooking – almost – meat will get more tender the longer you cook it in the crockpot. WHAT IF MY POT ROAST IS STILL A LITTLE TOUGH WHEN IT SHOULD BE DONE? Put the lid back on and let that pot roast cook longer. Previously: beef roast cook time.
In order to get the most flavor out of your beef, whether it is for a roast or for a stew, you must first sear it. When you pan sear beef, you quickly cook the outer surface of the meat at a high temperatures so that it caramelizes and forms a crust.
Place the meat, fat side up, on a rack in a shallow roasting pan. Roasts with a bone, such as a rib roast, don't need a rack. Do not add water or liquid and do not cover the roast. Covering the roast would result in more steaming than roasting in the oven so we cook a beef roast uncovered.
If it's not cooked correctly, that same cut of meat can be distressingly tough, chewy or dry. A failed pot roast can result from undercooking, overcooking or choosing the wrong cut of meat, so before you can fix it you'll need to decide where you've gone wrong.
You may be able to salvage a roast that's dry by adding more liquid. However, for meat that's tough, we like to repurpose it instead. Let the meat cool, then use forks or your fingers to pull the overcooked meat into shreds. Then, use the meat to create new dishes.
We suggest planning 30 additional minutes. Approximately 15 minutes for searing the roast at 450 °F prior to roasting and approximately 15 minutes for the roast to rest before serving .Common Names.
Cook for 20 minutes a pound. A 3.5 lb roast takes about 1 hour and 15 minutes for a rare roast, but watch the thermometer reading. After you cook it for 20 minutes a pound, take it out of the oven, let it sit for 1 minute and then check the thermometer reading. See also beef roast gravy recipe.
If you want your chuck roast to fall apart similar to pulled pork, you have to take the internal temperature of the meat up to around 190-195, in order to render all the fat and connective tissue. At 300 degrees, such a small roast will start to overcook before those tissues get a chance to melt away.
Reduce the heat to 190C/375F/Gas 5 and roast for half an hour per kilo for rare, adding another ten minutes per kilo for medium rare, 20 minutes per kilo for medium, and 30 minutes per kilo for well done. Remove the beef from the oven, transfer it to a carving board and cover with foil.
Chuck roast has more fat and connective tissue, so it tends to break into strands as it “melts”. That adds to the flavor and to the texture/mouth feel. Bottom round has less of the fat and connective tissue, so it holds together better and slices nicely, which makes for great pot roast sandwiches.
Chuck roast comes from a cow's shoulder portion. The hindquarters and shoulder area are both well-used parts of the cow, so these two cuts of meat are naturally pretty tough. Most people agree that roasted rump is the more tender of the two. Also check: beef roast grades.
The Chateaubriand beef tenderloin roast is considered to be the most tender cut of beef for a roast. This cut of beef comes from the loin area of the cow, which is right below the backbone, behind the rib section and in front of the sirloin section.
The top round is very lean but tends to be more tender than the bottom round, and is often cut into steaks (which are sometimes labeled "London broil"). The bottom round, which is divided into a bottom round roast and a rump roast, is a bit tougher. See also: beef roast quality.
Because it's essentially muscle meat, a top round roast is lean and very flavorful, but it lacks fat and marbleizing throughout – so it can be tougher, and not as juicy as roasts made from more expensive cuts of beef. See also: beef roast types.